Scalable power for railway applications

While the external design of trains often remains virtually unchanged over the years, electrification and the use of new technologies are constantly advancing. To increase reliability and safety, more and more mechanical components are being replaced by cheaper and less failure-prone electronic devices, monitoring systems allow better control of all functions, and communication with the central control station is constantly being expanded.

This development is most seen in the train driver's compartments, where monitors replaced analog meters or warning lights, and fewer switches and levers are used.  But even in non-visible areas, an increased number of computers, GPS systems, GSM communication units, and bus systems are used to process the numerous control signals across the complete train.     

One of the major challenges in this increasing electrification is the available space. The mechanical design of a train usually cannot be changed, and devices with more features and functionality combined with higher power requirements must fit into the space predetermined by the previous system. For the power supply, this means significantly higher power density and efficiency.

In order to not only save on development costs but also to reduce the number of different power solutions, manufacturers are looking for uniform solutions that can easily be adapted to the various voltage and power requirements of the respective application.

P-DUKE's new QBE family of DC/DC converters in the industry-standard quarter-brick format (57.9 x 36.8 mm or 2.28 x 1.45 inches) enables customers to design smaller, more powerful solutions, which can be adopted and scaled to an application by simply exchanging the module and a few external components.

In a specific example, a customer wanted to redesign a central door control unit to integrate more safety features, including ASDO (Automatic Selective Door Opening) using GPS information. Power requirements doubled from 12V/35W to 12V/70W. In addition, the customer wanted to save development costs by using the same power design for a door opener circuit requiring 24V/95W. 

The legacy system used a 40W converter with a footprint of 2 x 1 inches and an efficiency of 86% at 35W output power. Losses in the converter are

The heat was spread into the system over the surface of the module and an attached heatsink.

The new QBE75W module from P-DUKE, designed for harsh environmental conditions in rolling stock applications, uses advanced power technologies and achieves an efficiency of 91% at 70W load with losses of only 6.9W. Although power was doubled, losses only increased by 20% or 1.2W. Due to the improved thermal design of this module, most of this heat can be conducted via the baseplate to the metal chassis. This means less thermal stress for all other components.

The QBE family is available with input voltages of 24Vnom (9V – 36V), 48Vnom (18V – 75V), and 110Vnom (40V – 160V), which covers all train voltages, including brownouts and transients.

Why not use one module covering the complete range? The design with an input voltage range of 8:1 or 12:1 makes it difficult to maintain optimal efficiency across the entire input voltage range, as all components must support both high currents at low input voltages and high operating voltages at high input voltages.

Input current is calculated by the formula

This graphic shows the input currents for different working voltages at 91% efficiency and 70W output power

It is obvious that a “one size fits all” design can’t be ideal when looking for the highest power density and efficiency. Most railway systems are ordered and configured for a specific train application where the supply voltage never changes. All external components, like EMI filters, fuses, or connectors, can be optimized for this specific train, and only the PCB needs to be designed for the high currents and to accommodate all component variations.  

Like almost all CPU boards today, the one used in the door opener control already has an onboard VRM (voltage regulator module) generating the low supply voltages for the microprocessor from the 12V bus. All other voltages in the system for memories or interfaces are generated by lower-power DC/DC converters. High isolation barriers are needed for the interfaces, and a P-Duke module with 3000VDC isolation was selected.

For the electric door opener requiring 24V/95W, the customer can switch from a Half Brick module used in the legacy product to the QBE100W module. In the quarter brick format, it is 40% smaller, and the 4% higher efficiency reduces losses by 33%.

The QBE family is available with output voltages from 3.3V up to 54V. Electrical and EMI behavior and PCB layout are identical for the 75W and 100W versions. In this case, the design of the 100W solution was done in a few hours rather than in weeks or months. No extensive tests or expensive approvals are needed. And if an application requires a different output voltage? Replacing the module with another part from the same family, adjusting a few external components, and the job is done. 

Central Door Control

Door Opener